View VP-1608F_1334785.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

VP-1608F Digital Voice Processor Processor
FEATURES FEATURES ! Plays messages stored in external EPROM chips ! CVSD technique with adjustable sampling rate from 16K to 128K bps for different voice quality ! Dual-channel audio output ! Up to 64 segments per channel ! Built-in RC oscillator or use external clock GENERAL DESCRIPTIONS The VP-1608F is a CMOS voice processor chip based on the CVSD (Continuously Variable Slope Delta) modulation technique. The VP-1608F is exactly the same as the (now obsolete) VP-1608 except that it is packaged in 64-pin QFP instead of 68-pin PLCC. Note that although the dual channel output provided by the VP-1608F can be used as a stereo output, it will be hard to do so since the VP-880 Voice Development System does not allow voice digitization in stereo mode. ! ! ! ! Direct EPROM addressing up to 8M bits Low power, single voltage operation Microprocessor interface Low-cost VP-880 system available for quick and easy voice development
Therefore the dual channel output is usually used in applications where sound synchronization is not critical. For example, in a game equipment, channel A can be playing a continuous background sound while channel B plays short sound effects based on the player's action. The dual channel output is available on two separate output pins. They can be used independently, or mixed together externally. Each channel may control up to 64 sound segments stored in 4 different EPROM banks, with up to 16 segments in each bank. Each segment stored in the EPROM is represented by a unique binary code: 2 bits for the bank code and 4 bits for the segment code. A valid code plus a strobe signal are all it takes to activate a certain segment. The VP-1608F can operate in a wide range of sampling rates (from 16 to 128 Kbps). A higher sampling rate usually produces better sound quality at the expense of higher memory cost. As a rule of thumb, start with 32 Kbps. A 1M EPROM can store 32 seconds of sound at this rate. Thanks to the chip's high internal integration, very little external components are required to build a VP-1608F based design. The VP-880 Voice Development System is available for quick and easy in-house voice development. APPLICATIONS ! Dual channel, multiple message playback ! Sound effects generator ! Digital announcer for consumer, industrial, security and telecommunication products
VP-1608F (QFP44) Pin Assignment
Eletech Enterprise Co., Ltd. 531-3F Chung-Cheng Road Hsin Tien, Taipei Hsien, Taiwan Tel:+886 2-2218-0068 Fax:+886 2-2218-0254
www.eletech.com
Eletech Electronics, Inc. 16025 Kaplan Avenue Industry, CA 91744, U.S.A. Tel: (626) 333-6394 Fax: (626) 333-6494
Supply Voltage, VCC - VDS .................................. 0 to 5.5V Input Volotage, VIN ........................................... VDS to VCC Operating Temperature, TOP ...................... -10oC to 60oC Storage Temperature, TST .......................... -20oC to 80oC
ABSOLUTE MAXIMUM RATINGS*
* Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
ELECTRICAL CHARACTERISTICS
Symbol VCC IDD IDRIVE ISINK VIH VIL FC FS TRESET TSI TSIE TDSP TRP TDS TDH TDL TECS TREAD TAH Parameter Supply Voltage Standby Current Output Current VOH=2.4V Output Current VOL=0.4V Input Voltage (High) Input Voltage (Low) Internal Scan Clock Sampling Clock Reset Pulse Width Strobe Input Pulse Width Strobe Inhibit Time After EOS (1) Delay Time From Strobe To Play Edge-Triggered Reset Interval Data Setup Time For INA ~ INF Data Hold Time For INA ~ INF Internal Load Pulse For INA ~ INF Address Valid Time For Ch. B EPROM Internal Latch Pulse For Ch. B EPROM Data Address Stable Time For Ch. B
(2)
Min. 4.5
Typ. 5 50 4 4 3.5 1.5
Max. 5.5
Units V uA mA mA V V
20
8 32 1 1 1.5
128
MHz KHz us us
150 1 350 1 65 250 65 125
ms ms us ns us ns ns ns ns
Note: (1) EOS = End-Of-Speech (2) Based on 1M EPROM scanning.
VOICE VP-1608..........................................................................................2
TIMING DIAGRAM
STROBE SPEECH ACTIVE BUSY RESET FC INTERNAL TIMING CLOCK STROBE INA ~ INF INTERNAL LATCH CLOCK INTERNAL LOAD CLOCK FC ADDRESS ECS LATCH CLOCK FOR CHB DATA (INTERNAL)
TSI TDSP TSIE TRP TDSP
TDS TDH TDL
TECS TAH TREAD
TEST CIRCUIT FOR I/O PIN
I/O
STROBE BUSY
VP-1608
VOICE VP-1608..........................................................................................3
PIN DESCRIPTIONS
A0 ~ A19: Address output to EPROM. Both channels share the same address lines in a 50-50 time sharing fashion. Pin ECS (described below) must be examined to tell who's address is valid at any particular moment. ANG1 & ANG1\: Differential audio output for channel A, connect to LM324 or LM358. ANG2 & ANG2\: Differential audio output for channel B, connect to LM324 or LM358. ANGD1: Audio feedback input for channel A. ANGD2: Audio feedback input for channel B. D0 ~ D7: Data input from EPROM. ECS: EPROM Channel Select output. This signal is used to indicate who's address is on the address lines. When the ECS is low, the address is for channel A. When the ECS is high, the address is for channel B. If both channels share one EPROM, this signal is usually connected to the highest address line so that each channel uses exactly half the EPROM space. If more than one EPROM are used, this signal is usually used by the address decoder to select the proper EPROM. ENV1: Envelop input for channel A, to be connected to INT1 with a feedback resistor.
Block Diagram
I/O1 RESET1 INA ~ IND CHA SEGMENT CONTROL ANGD1 ANG1 ANG1 ENV1 INT1
CHA CVSD DEMODULATOR
INE, INF SE, SF
BANK CONTROL
CHA FLAG RECEIVER
CHB SEGMENT CONTROL I/O2 RESET2 VCC VDS VAS CHA & CHB TIME SHARING CIRCUIT
CHB FLAG RECEIVER
D0 ~ D7 ANGD2 ANG2 ANG2 ENV2 INT2 ECS
CHB CVSD DEMODULATOR
OSC1 & OSC2
CHA CLOCK & ADDRESS GENERATOR HIGH SPEED SPINNER CHB CLOCK & ADDRESS GENERATOR ADDRESS MULTIPLEXER
A0 ~ A19
VOICE VP-1608..........................................................................................4
ENV2: Envelop input for channel B, to be connected to INT2 with a feedback resistor. INT1: Integrator output for channel A, to be connected to an external RC integration circuitry. INT2: Integrator output for channel B, to be connected to an external RC integration circuitry. I/O1: Strobe input/Busy output for channel A, active low. To play a message on channel A, place the segment/bank code on INA to INE and strobe this pin with a low pulse. During the playback this pin becomes an active-low "busy" output. If this pin is held low at the end of playback, the message will be re-triggered. I/O2: Same as I/O1 except that this pin is for channel B. INA ~ IND: Input for segment code in binary format. INA is the LSB and IND is the MSB. INE, INF: Input for bank code in binary format, max. 4 banks. INE is the LSB and INF is the MSB.
OSC1, OSC2: Internal oscillator pins for external RC components. It external clock source is to be used, feed it through the OSC2 pin. Note that both channels share the same clock, so their sampling rate must be the same. RESET1: Reset input for channel A, active low. On the falling edge of this reset signal, channel A playback is stopped and all internal counters for channel A are cleared. RESET2: Reset input for channel B, active low. On the falling edge of this reset signal, channel B playback is stopped and all internal counters for channel B are cleared. SCK, TEST: For factory use only, do not make any connection. SE, SF: Output for EPROM bank select. These two pins are actually latched outputs for INE and INF. VDD: Input, supply voltage. VDS & VAS: VDS is digital ground and VAS is analog ground. Connect the two grounds together close to the power source to minimize noise.
APPLICATION NOTES
1. EOM (End Of Message) Flag The EOM flag consists of six consecutive bytes of "AA", or "10101010" in binary format. After a trigger signal is received, the VP-1608 uses the internal 8MHz system clock to scan through memory space and finds the correct message by counting the number of EOM flags. For example, to find the 5th message, it must scan through each and every memory location until it finds 4 EOM flags. The first byte following the 4th EOM flag is the first byte of the 5th message. 2. Creating Master EPROM File on the VP-880 System Follow these steps to create the master EPROM file: 1. To maximize the EPROM usage, arrange your sound segments in banks of 16 or less, so that the total combined length for each bank is about the same. Do not mix channel A and channel B together. 2. Based on the total combined length of the largest bank, select a highest sampling rate that will fully utilize the EPROM. Use the following equation: Sampling Rate (Kbps) = EPROM Size (K-bits) / Total Length (Second) 3. Digitize and edit each segment as a separate file. Use the "ROM Data Management" function to combine up to 16 messages into a "bank file". The first filename entered in the "ROM Data Management" is the first segment in that bank, and etc. 4. Depending on the hardware design, each EPROM chip may contain one or more sound banks. It is also possible to use just one EPROM to store all sound segments of both channel A and channel B. If you need to combine several bank files into one for programming into one EPROM chip, use the following DOS command: COPY /b file_1+file_2+..+file_n destination_file Do not use the "ROM Data Management" function to combine bank files, otherwise each bank file will be considered as a single message file.
VOICE VP-1608..........................................................................................5
5
4
3
2
1
D
D
+5V VP1608F
58 1 2 3 4 5 6 VCC INA INB INC IND INE INF I/O1 A16 A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 SE SF ECS 14 INT2 ANG1 + 16 ENV2 ANG1
B
+5V 27C080
52 50 49 47 48 41 38 43 45 46 44 42 40 39 37 35 33 34 30 28 26 24 25 27 29 55 56 57 8 2 3 29 28 4 25 23 26 27 5 6 7 8 9 10 11 12 21 20 19 18 17 15 14 13 30 31 1 A16 A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 A17 A18 A19 VCC 32
TO EXTERNAL CONTROLLER
C
1N4148
59
1N4148
60 I/O2
C
7 36
RESET1 RESET2 INT1
3K
13
+
1uF 3K
15
CE CS GND
24 22 16 11
ENV1
+5V
1 U19
9 21 10
390K
19 OSC1 ANGD1 ANG2 OSC2
472
472
4
VR 50K
3 7 INBP
OUT GAIN
5 8
+
22 61
VAS VDS
ANG2 ANGD2
11 23
A
5
4
+
5
472
472
3
+
240
-
6
33K
33K
10
7
-
VR 500K
20
+
1uF
12
LM324
9
+
240
-
13
33K
33K
3
14
-
LM324
2
220uF
LS1
LM324 +5V
104
6
VC
B
SPEAKER
+ 8
472 10
GAIN 1
10uF 104
2 4 IN+ GND LM386-3
LM324
A
2
1

▲Up To Search▲

Price & Availability of VP-1608F

	To Download VP-1608F Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .